A NEW ALGORITHM FOR ADAPTIVE LATTICE FILTERAND ITS APPLICATION IN THE SPEECH LINEARPREDICTIVE SYNTHESIS

In this paper, an adaptive line spectral pair filter is derived from an adaptive lattice filter. A least-mean-square(LMS) type adaptive algorithm used to calculate directly the line spectral pair(LSP) coefficients on a stage-by-stage basis is presented. Experimental results show that the algorithm has higher convergence rate and lower misadjustment as compared with the other algorithms. The LSP coefficients calculated by the algorithm have been used to carry out speech linear predictive synthesis, resulting in better results than PARCOR coefficients.     

高速波长可调液晶滤波器

描述了适用于光波分复接网络高速连续可调液晶滤波器。该滤波器利用手征近晶型液晶作为Ｆ－Ｐ标准具有源腔材料得到了微秒级开关速度。使用商品 ＢＤＨ７６４Ｅ液晶材料制成地光滤波器，开关速度小于１０μｓ，可调范围给３０ｎｍ，通带中心在１．５５μｍ。     

高阻带抑制有源声表面波滤波组件

介绍有源声表面波滤波组件的设计思路。报道最新研制的高性能滤波组件，其中心频率４０ＭＨｚ，３ｄＢ相对带宽０．８％，阻带抑制优于１００ｄＢ，矩形系数（Δｆ１００ｄＢ／Δｆ３ｄＢ）小于３，输入输出端口电压驻波比接近１。组件体积８５ｍｍ×３５ｍｍ×２４ｍｍ，重量小于１１５ｇ     

纸张背衬不同衬底时的光反射率的研究

从理论上研究了纸张背衬不同衬底的光反射率，得出下列表达式：Ｒｂ＝Ｒｏ＋（Ｒ∞－Ｒｏ）×（１／Ｒ∞－Ｒｏ）／（１／Ｂ－Ｒｏ）（Ｂ为衬底的光反射率），该式简单实用且物理意义明确。利用上述公式，可将Ｔａｐｐｉ标准列出的Ｔａｐｐｉ不透明度Ｃ０．８９的换算公式简化，并可从理论上定性地讨论纸张不透明度与印刷透印性的关系。     

声表面波传感器电路参数的CAD方法

本文提出了声表面波传感器电路参数的一种ＣＡＤ方法，即有约束内点惩罚函数－鲍威尔－阻尼最小二乘法，并对两个实例进行了计算。     

Direct preparation of particles from liquid suspension for ESEM or SEM analysis

A simplified method for the preparation of particles from liquid suspensions has been developed. Particles are deposited directly on carbon planchets for rapid analysis by environmental scanning electron microscopy or by conventional scanning electron microscopy after an additional drying step. This is accomplished by filtering the liquid through thin carbon planchets. Three different grades of graphite were investigated for their suitability as the source material for these planchets. The high quality isomolded graphite is recommended for the filtration and direct observation of particles by electron microscopy. This technique is demonstrated for particles in hydraulic fluid and aquatic suspended particulate material from a natural water source.     

大截面金属镍棒的焊接工艺与实践

金属镍在电渣精炼前需用氩弧焊焊接接长,为保证焊接接头具有足够熔深,需要大参数进行焊接.采用直流焊机并联使用解决了焊机电流不足的情况,通过采取垫高镍棒端头,使接缝处于受压状态,以防止裂纹的产生.     

An attempt to compare the performance of bioscrubbers and biotrickling filters for degradation of ethyl acetate in gas streams

This study presents a comparison of the efficiency of a bioscrubber and a biotrickling filter (BTF) for the removal of ethyl acetate (EA) vapour from a waste gas stream, under the same operating conditions. The maximum EA elimination capacity achieved in the bioscrubber was 550 g m^?3 h^?1 with removal efficiency higher than 96%. For higher EA loadings the bioscrubber was oxygen limited, which caused incomplete EA biodegradation. When pure oxygen was fed to the bioscrubber at a rate of 0.02 L min^?1, the bioscrubber recovered and could treat higher EA loadings without any oxygen limitation. The BTF achieved EA elimination capacity of 600 g m^?3 h^?1 with removal efficiency higher than 97% and the dissolved oxygen concentration remained substantially higher than in the bioscrubber. However, severe channelling and blockage of the spray nozzle occurred due to the excessive biomass growth. Overall, the bioscrubber system was easier to operate and control than the BTF, while an enhancement of the oxygen mass transfer in the bioscrubber could potentially increase its performance by up to three times. Copyright © 2005 Society of Chemical Industry     

斜井抽油系统优化设计技术研究及应用

结合斜井井身轨迹特点,建立了斜井三维井眼中杆柱轴向载荷和侧向载荷计算数学模型,给出扶正器间距和加重杆配置的计算方法;应用系统工程分析方法,给出系统参数设计的步骤,形成了斜井有杆泵抽油系统抽汲参数优化设计方法,编制了相应的优化设计软件。现场应用实例表明,该优化设计方法理论正确可靠,根据本方法编制的斜井抽油系统优化设计软件用于现场设计,可达到有效降低管杆偏磨,减小悬点载荷,提高油井产量、泵效和井下系统效率之目的。     

对水厂一期滤池技术改造后的经济评价

本文主要从经济角度分析净水厂实际生产情况及经济技术指标等方面的数据。阐述福州西区水厂一期滤池由原先双阀滤池改造成V型滤池的经济性。